top of page

Maintenance Detective: The Motor That Never Finished Starting

Oct 21
4 min read

A 75 HP hydraulic pump motor on a star-delta starter for an injection molder has started acting up.


At idle, it sounds fine. Spins up, settles in.  Normal.


But as soon as the machine starts cycling and the pump picks up real load, the motor bogs down. 


Sounds like it has too much load.


Cycle times stretch longer than normal. The motor case is too hot to keep your hand on and the overload is tripping a couple times per shift. Techs are just resetting it.


The day shift tech already did the smart stuff. Megger test passed. Winding resistances are balanced. Bearings are quiet. Pump was checked and isn't binding or vibrating. Supply voltage is good on all three legs.


One more clue. The operator who has run this machine for eleven years says (with big hand movements): "It used to go clunk...... clunk when it started. Now it just goes clunk."


What failed, and how would you prove it before you start swapping parts?










Answer:


The culprit: the star-delta timer relay welded shut, and the motor is stuck running in star.


First, how a star-delta starter is supposed to work.


Large motors pull a huge inrush when started across the line. A star-delta starter reduces inrush by starting the motor with its windings connected in star (wye), then switching them to delta once the motor is up to speed.


In star, each winding only sees line voltage divided by √3, about 58%. Torque goes with voltage squared, so starting torque and starting current both drop to roughly one third of a direct-on-line start. That's the whole point: a softer start on the motor, the coupling, the pump, and the plant electrical system.


The sequence runs like this: Start command → main and star contactors pull in (clunk) → timer relay starts timing → motor accelerates on reduced voltage → timer times out → star drops out, delta pulls in (clunk) → motor runs on full voltage with full torque.


Two clunks. Every start.


What a welded timer does to that sequence.


On most units, the timer's timed contact is what tells the circuit "time's up, switch to delta." In the common wiring, the timer has a contact that holds the star coil energized during the timing period and opens when it times out, letting the delta coil pick up.


Weld that contact shut and the time-out never happens as far as the circuit is concerned. Star stays in. Delta never gets the signal. The electrical interlock (star aux contact in the delta coil circuit) keeps delta locked out the entire time.


One clunk. Forever.


A note for the sharp-eyed: which way a welded timer fails depends on which contact welded and how that particular starter is wired. Weld a different contact and you can get the opposite symptom: no star stage at all and a violent across-the-line start that pops fuses. Always read the print for your unit.


Why it looks like a mechanical problem.


Stuck in star, the motor only has about one third of its normal torque available. That's why it fools people.


At idle or light load, one third of rated torque is plenty. The motor spins up close to normal speed and sounds healthy.


Under real hydraulic load, the motor can't produce the torque the pump is asking for. Slip climbs, speed sags, and the windings carry more current than they should for the voltage they're seeing. 


That explains your heat, your sluggish cycle, and your overload trips. It's also why the problem gets "worse when the machine is working hard," which sends a lot of techs chasing the pump, the bearings, and the hydraulics.


Every check the day shift did was correct. They just ruled out the motor and the load. They never looked at what the starter was asking the motor to do.


How to prove it in about five minutes.


  1. Watch and listen at the starter during a start. Confirm the star contactor pulls in and stays in well past the normal transition time, and that the delta contactor never picks up.

  2. Check the timer output. With a meter on the timer's timed contact, verify whether it changes state at the set time. A welded contact will show continuity the whole time, before and after time-out. Then do it LOTO'd and confirm with an ohm check on the de-energized relay.

  3. Rule out the delta side. If the timer is switching but delta still won't pull in, check for coil voltage at the delta contactor. No voltage means a control wiring or interlock fault upstream. Voltage present but no pull-in means a failed contactor.

  4. Confirm with a clamp meter under load. Compare running current and speed against nameplate. A motor that only behaves at light load and falls apart under load fits the star-lock picture.


Don't just swap the timer.


A timer relay that's only switching contactor coils is a very low-energy duty. Those contacts shouldn't weld under normal conditions. If one did, check for potential additional loading on that contact. Check for:


  • Missing or failed coil suppression (RC snubber, varistor, or diode) on the contactor coils. Without it, the inductive kick when a coil drops out arcs across the timer contacts every single start.

  • An undersized contact rating for the coil load actually being switched.

  • A downstream fault, like a shorted coil or a wiring fault, that pushed real current through the contact.

  • Component quality, especially if the timer was a "close enough" replacement.


Replacing the timer with an additional problem left undiagnosed just gives you more work later.


Check the motor before you call it fixed.


This motor has been running hot under load for who knows how long. After the repair, check case temperature over a full production run and consider a follow-up megger test to make sure the heat didn't take a bite out of the insulation.


The lesson: When a motor tests healthy and the load tests healthy but the system still struggles, look at what the controls are telling the motor to do. Sometimes the best diagnostic tool in the plant is the operator who knows how the machine is supposed to sound.


Recurring equipment issues cost more than repair time. They create downtime, interrupt production, and keep maintenance teams responding to the same issues.


180 OPEX helps manufacturers build the systems that prevent recurring problems and keep operations running consistently.


If your team is spending too much time responding to recurring issues, let's talk.



Comments


bottom of page